Move curlx_ functions into its own subdir.
The idea is to use the curlx_ prefix proper on these functions, and use
these same function names both in tool, lib and test suite source code.
Stop the previous special #define setup for curlx_ names.
The printf defines are now done for the library alone. Tests no longer
use the printf defines. The tool code sets its own defines. The printf
functions are not curlx, they are publicly available.
The strcase defines are not curlx_ functions and should not be used by
tool or server code.
dynbuf, warnless, base64, strparse, timeval, timediff are now proper
curlx functions.
When libcurl is built statically, the functions from the library can be
used as-is. The key is then that the functions must work as-is, without
having to be recompiled for use in tool/tests. This avoids symbol
collisions - when libcurl is built statically, we use those functions
directly when building the tool/tests. When libcurl is shared, we
build/link them separately for the tool/tests.
Assisted-by: Jay Satiro
Closes#17253
"asyn" is the internal name under which both c-ares and threaded
resolver operate. Make the naming more consistent. Implement the c-ares
resolver in `asyn-ares.*` and the threaded resolver in `asyn-thrdd.*`.
The common functions are in `asyn-base.c`.
When `CURLRES_ASYNCH` is defined, either of the two is used and
`data->state.async` exists. Members of that struct vary for the selected
implementation, but have the fields `hostname`, `port` and `ip_version`
always present. This are populated when the async resolving starts and
eliminate the need to pass them again when checking on the status and
processing the results of the resolving.
Add a `Curl_resolv_blocking()` to `hostip.h` that relieves FTP and SOCKS
from having to repeat the same code.
`Curl_resolv_check()` remains the function to check for status of
ongoing resolving. Now it also performs internally the check if the
needed DNS entry exists in the dnscache and if so, aborts the asnyc
operation. (libcurl right now does not check for duplicate resolve
attempts. an area for future improvements).
The number of functions in `asyn.h` has been reduced. There were subtle
difference in "cancel()" and "kill()" calls, both replaced by
`Curl_async_shutdown()` now. This changes behaviour for threaded
resolver insofar as the resolving thread is now always joined unless
`data->set.quick_exit` is set. Before this was only done on some code
paths. A future improvement would be a thread pool that keeps a limit
and also could handle joins more gracefully.
DoH, not previously tagged under "asny", has its struct `doh_probes` now
also in `data->state.async`, moved there from `data->req` because it
makes more sense. Further integration of DoH underneath the "asyn"
umbrella seems like a good idea.
Closes#16963
by including headers using "../[header]" when done from C files in
subdirectories, we do not need to specify the lib source dir as an
include path and we reduce the risk of header name collisions with
headers in the SDK using the same file names.
Idea-by: Kai Pastor
Ref: #16949Closes#16991
With rustls-ffi 0.15+ we can set up a callback for writing TLS secrets
hooked up to call Curl_tls_keylog_write. To make sure the associated
file is cleaned up we update the Curl_ssl struct for the rustls-ffi vtls
backend to have a cleanup callback.
Closes#16828
Allowing 4GB on a 32-bit system is just asking for problems and could in
theory cause integer overflow in the dynbuf code.
The dynbuf now has an assert to catch code trying to set a max larger
than half SIZE_T_MAX.
Reported-by: Rinku Das
Closes#16716
Before this patch, standard `E*` errno codes were redefined on Windows,
onto matching winsock2 `WSA*` error codes, which have different values.
This broke uses where using the `E*` value in non-socket context, or
other places expecting a POSIX `errno`, e.g. file I/O, threads, IDN or
interfacing with dependencies.
Fix it by introducing a curl-specific `SOCKE*` set of macros that map to
`WSA*` on Windows and standard POSIX codes on other platforms. Then
verify and update the code to use `SOCKE*` or `E*` macro depending on
context.
- Add `SOCKE*` macros that map to either winsock2 or POSIX error codes.
And use them with `SOCKERRNO` or in contexts requiring
platform-dependent socket error codes.
This fixes `E*` uses which were supposed be POSIX values, not `WSA*`
socket errors, on Windows:
- lib/curl_multibyte.c
- lib/curl_threads.c
- lib/idn.c
- lib/vtls/gtls.c
- lib/vtls/rustls.c
- src/tool_cb_wrt.c
- src/tool_dirhie.c
- Ban `E*` codes having a `SOCKE*` mapping, via checksrc.
Authored-by: Daniel Stenberg
- Add exceptions for `E*` codes used in file I/O, or other contexts
requiring POSIX error codes.
Also:
- ftp: fix missing `SOCKEACCES` mapping for Windows.
- add `SOCKENOMEM` for `Curl_getaddrinfo()` via `asyn-thread.c`.
- tests/server/sockfilt: fix to set `SOCKERRNO` in local `select()`
override on Windows.
- lib/inet_ntop: fix to return `WSAEINVAL` on Windows, where `ENOSPC` is
used on other platforms. To simulate Windows' built-in `inet_ntop()`,
as tested on a Win10 machine.
Note:
- WINE returns `STATUS_INVALID_PARAMETER` = `0xC000000D`.
- Microsoft documentation says it returns `WSA_INVALID_PARAMETER`
(= `ERROR_INVALID_PARAMETER`) 87:
https://learn.microsoft.com/windows/win32/api/ws2tcpip/nf-ws2tcpip-inet_ntop#return-value
- lib/inet_ntop: drop redundant `CURL_SETERRNO(ENOSPC)`.
`inet_ntop4()` already sets it before returning `NULL`.
- replace stray `WSAEWOULDBLOCK` with `USE_WINSOCK` macro to detect
winsock2.
- move existing `SOCKE*` mappings from `tests/server` to
`curl_setup_once.h`.
- add missing `EINTR`, `EINVAL` constants for WinCE.
Follow-up to abf80aae38#16612
Follow-up to d69425ed7d#16615
Bug: https://github.com/curl/curl/pull/16553#issuecomment-2704679377Closes#16621
This allows you to use the `certs` and `num_certs` writeout variables in
the curl tool, and getting information about the server certificates
using CURLINFO_CERTINFO.
Closes#16459
Make it possible to build curl for Windows CE using the CeGCC toolchain.
With both CMake and autotools, including tests and examples, also in CI.
The build configuration is the default one with Schannel enabled. No
3rd-party dependencies have been tested.
Also revive old code to make Schannel build with Windows CE, including
certificate verification.
Builds have been throughougly tested. But, I've made no functional tests
for this PR. Some parts (esp. file operations, like truncate and seek)
are stubbed out and likely broken as a result. Test servers build, but
they do not work on Windows CE. This patch substitutes `fstat()` calls
with `stat()`, which operate on filenames, not file handles. This may or
may not work and/or may not be secure.
About CeGCC: I used the latest available macOS binary build v0.59.1
r1397 from 2009, in native `mingw32ce` build mode. CeGCC is in effect
MinGW + GCC 4.4.0 + old/classic-mingw Windows headers. It targets
Windows CE v3.0 according to its `_WIN32_WCE` value. It means this PR
restores portions of old/classic-mingw support. It makes the Windows CE
codepath compatible with GCC 4.4.0. It also adds workaround for CMake,
which cannot identify and configure this toolchain out of the box.
Notes:
- CMake doesn't recognize CeGCC/mingw32ce, necessitating tricks as seen
with Amiga and MS-DOS.
- CMake doesn't set `MINGW` for mingw32ce. Set it and `MINGW32CE`
manually as a helper variable, in addition to `WINCE` which CMake sets
based on `CMAKE_SYSTEM_NAME`.
- CMake fails to create an implib for `libcurl.dll`, due to not
recognizing the platform as a Windowsy one. This patch adds the
necessary workaround to make it work.
- headers shipping with CeGCC miss some things curl needs for Schannel
support. Fixed by restoring and renovating code previously deleted
old-mingw code.
- it's sometime non-trivial to figure out if a fallout is WinCE,
mingw32ce, old-mingw, or GCC version-specific.
- WinCE is always Unicode. With exceptions: no `wmain`,
`GetProcAddress()`.
- `_fileno()` is said to convert from `FILE *` to `void *` which is
a Win32 file `HANDLE`. (This patch doesn't use this, but with further
effort it probably could be.)
https://stackoverflow.com/questions/3989545/how-do-i-get-the-file-handle-from-the-fopen-file-structure
- WinCE has no signals, current directory, stdio/CRT file handles, no
`_get_osfhandle()`, no `errno`, no `errno.h`. Some of this stuff is
standard C89, yet missing from this platform. Microsoft expects
Windows CE apps to use Win32 file API and `FILE *` exclusively.
- revived CeGCC here (not tested for this PR):
https://building.enlyze.com/posts/a-new-windows-ce-x86-compiler-in-2024/
On `UNDER_CE` vs. `_WIN32_WCE`: (This patch settled on `UNDER_CE`)
- A custom VS2008 WinCE toolchain does not set any of these.
The compiler binaries don't contain these strings, and has no compiler
option for targeting WinCE, hinting that a vanilla toolchain isn't
setting any of them either.
- `UNDER_CE` is automatically defined by the CeGCC compiler.
https://cegcc.sourceforge.net/docs/details.html
- `UNDER_CE` is similar to `_WIN32`, except it's not set automatically
by all compilers. It's not supposed to have any value, like a version.
(Though e.g. OpenSSL sets it to a version)
- `_WIN32_WCE` is the CE counterpart of the non-CE `_WIN32_WINNT` macro.
That does return the targeted Windows CE version.
- `_WIN32_WCE` is not defined by compilers, and relies on a header
setting it to a default, or the build to set it to the desired target
version. This is also how `_WIN32_WINNT` works.
- `_WIN32_WCE` default is set by `windef.h` in CeGCC.
- `_WIN32_WCE` isn't set to a default by MSVC Windows CE headers (the
ones I checked at least).
- CMake sets `_WIN32_WCE=<ver>`, `UNDER_CE`, `WINCE` for MSVC WinCE.
- `_WIN32_WCE` seems more popular in other projects, including CeGCC
itself. `zlib` is a notable exception amongst curl dependencies,
which uses `UNDER_CE`.
- Since `_WIN32_WCE` needs "certain" headers to have it defined, it's
undefined depending on headers included beforehand.
- `curl/curl.h` re-uses `_WIN32_WCE`'s as a self-guard, relying on
its not-(necessarily)-defined-by-default property:
25b445e479/include/curl/curl.h (L77)
Toolchain downloads:
- Windows:
https://downloads.sourceforge.net/cegcc/cegcc/0.59.1/cegcc_mingw32ce_cygwin1.7_r1399.tar.bz2
- macOS Intel:
https://downloads.sourceforge.net/cegcc/cegcc/0.59.1/cegcc_mingw32ce_snowleopard_r1397.tar.bz2Closes#15975
Remove `blocking` argument from cfilter's connect method.
Implement blocking behaviour in Curl_conn_connect() instead for all
filter chains.
Update filters implementations. Several of which did never use the
paramter (QUIC for example). Simplifies connect handling in TLS filters
that no longer need to loop
Fixed a blocking connect call in FTP when waiting on a socket accept()
which only worked because the filter did not implement it.
Closes#16397
For TLS backends that don't need these functions, they now use plain
NULL pointers instead of setting a function that does nothing.
Helps making it clearer that a specific TLS handler does not provide
anything specific for that action.
Closes#15772
Build wolfSSL master with
./configure --prefix=/path --enable-ip-alt-name --enable-quic
--enable-earlydata --enable-psk --enable-opensslcoexist
and configure curl with openssl + wolfssl. Normal tests run.
pytest session resumption fails, as wolfssl does not handle the
new_session callback without opensslextra right now.
Closes#15481
That error code was introduced and has been used for OpenSSL ENGINE
things and not others, so switch the other use cases over to other TLS
related error codes.
Closes#15430
Based on #14135, implement TLSv1.3 earlydata support for the curl
command line, libcurl and its implementation in GnuTLS.
If a known TLS session announces early data support, and the feature is
enabled *and* it is not a "connect-only" transfer, delay the TLS
handshake until the first request is being sent.
- Add --tls-earldata as new boolean command line option for curl.
- Add CURLSSLOPT_EARLYDATA to libcurl to enable use of the feature.
- Add CURLINFO_EARLYDATA_SENT_T to libcurl, reporting the amount of
bytes sent and accepted/rejected by the server.
Implementation details:
- store the ALPN protocol selected at the SSL session.
- When reusing the session and enabling earlydata, use exactly
that ALPN protocol for negoptiation with the server. When the
sessions ALPN does not match the connections ALPN, earlydata
will not be enabled.
- Check that the server selected the correct ALPN protocol for
an earlydata connect. If the server does not confirm or reports
something different, the connect fails.
- HTTP/2: delay sending the initial SETTINGS frames during connect,
if not connect-only.
Verification:
- add test_02_32 to verify earlydata GET with nghttpx.
- add test_07_70 to verify earlydata PUT with nghttpx.
- add support in 'hx-download', 'hx-upload' clients for the feature
Assisted-by: ad-chaos on github
Closes#15211
booleans should use the type 'bool' and set the value to TRUE/FALSE
non-booleans should not be 'bool' and should not set the value to
TRUE/FALSE
Closes#15123
Now that the curl rustls vtls backend is using rustls 0.14 we can
address the weak random situation by using
`rustls_default_crypto_provider_random()` to provide a `Curl_ssl`
`random` callback that fills the provided buffer with cryptographically
secure random data.
The mentions in `docs/` about weak RNG when using rustls are removed as
they are no longer applicable.
Closes#14889
Now that the rustls vtls backend is using rustls 0.14 we can take
advantage of `rustls_supported_ciphersuite_protocol_version()` to skip
TLS 1.3 and TLS 1.2 ciphersuites as required without needing to
interrogate the ciphersuite names as `rustls_str`s.
Closes#14889
* Documentation is updated to describe new required version, and to link
to the upstream README about cryptography providers.
* GitHub workflow is updated to fetch 0.14.0.
* Breaking changes in`lib/vtls/rustls.c` are addressed:
* The `rustls_client_config_builder_build()` function now uses an out
parameter for the built config instead of returning it directly.
This allows the building process to fail if the default crypto
provider state isn't appropriate, or another error condition occurs.
* Default ciphersuites are collected using renamed functions named to
make it clear the ciphersuites are associated with the default
crypto provider.
* Customization of ciphersuites is now done via
a `rustls_crypto_provider_builder` used to instantiate a
`rustls_crypto_provider`. The customized provider can then can be
used with `rustls_client_config_builder_new_custom` in place of
providing ciphersuites directly.
* `rustls_connection_get_negotiated_ciphersuite()` now returns the
ciphersuite ID directly.
Closes#14889
It's easier to diagnose a problem when there is one place where the
error message can be emitted. For that reason this commit updates two
errors that were shared between other fallible operations to use unique
messages.
Closes#14889
Don't build `config_builder` just to free the resulting config, free the
builder directly.
When `cr_init_backend` encounters an error condition setting up the
Rustls client configuration it must do something with the
`config_builder` that was constructed earlier to avoid a memory leak.
The previous implementation preferred to use a pattern of building the
builder (thus consuming it) and then freeing the built config (to avoid
a memory leak). However, the purpose/intent is clearer when we just free
the builder directly instead of building it and freeing the result.
Closes#14889
Channel Bindings are used to tie the session context to a specific TLS
channel. This is to provide additional proof of valid identity,
mitigating authentication relay attacks.
Major web servers have the ability to require (None/Accept/Require)
GSSAPI channel binding, rendering Curl unable to connect to such
websites unless support for channel bindings is implemented.
IIS calls this feature Extended Protection (EPA), which is used in
Enterprise environments using Kerberos for authentication.
This change require krb5 >= 1.19, otherwise channel bindings won't be
forwarded through SPNEGO.
Co-Authored-By: Steffen Kieß <947515+steffen-kiess@users.noreply.github.com>
Closes#13098
Adds a `bool eos` flag to send methods to indicate that the data
is the last chunk the invovled transfer wants to send to the server.
This will help protocol filters like HTTP/2 and 3 to forward the
stream's EOF flag and also allow to EAGAIN such calls when buffers
are not yet fully flushed.
Closes#14220
Adds a `bool eos` flag to send methods to indicate that the data is the
last chunk the invovled transfer wants to send to the server.
This will help protocol filters like HTTP/2 and 3 to forward the
stream's EOF flag and also allow to EAGAIN such calls when buffers are
not yet fully flushed.
Closes#14220
Based on the standards and guidelines we use for our documentation.
- expand contractions (they're => they are etc)
- host name = > hostname
- file name => filename
- user name = username
- man page => manpage
- run-time => runtime
- set-up => setup
- back-end => backend
- a HTTP => an HTTP
- Two spaces after a period => one space after period
Closes#14073
When libcurl discards a connection there are two phases this may go
through: "shutdown" and "closing". If a connection is aborted, the
shutdown phase is skipped and it is closed right away.
The connection filters attached to the connection implement the phases
in their `do_shutdown()` and `do_close()` callbacks. Filters carry now a
`shutdown` flags next to `connected` to keep track of the shutdown
operation.
Filters are shut down from top to bottom. If a filter is not connected,
its shutdown is skipped. Notable filters that *do* something during
shutdown are HTTP/2 and TLS. HTTP/2 sends the GOAWAY frame. TLS sends
its close notify and expects to receive a close notify from the server.
As sends and receives may EAGAIN on the network, a shutdown is often not
successful right away and needs to poll the connection's socket(s). To
facilitate this, such connections are placed on a new shutdown list
inside the connection cache.
Since managing this list requires the cooperation of a multi handle,
only the connection cache belonging to a multi handle is used. If a
connection was in another cache when being discarded, it is removed
there and added to the multi's cache. If no multi handle is available at
that time, the connection is shutdown and closed in a one-time,
best-effort attempt.
When a multi handle is destroyed, all connection still on the shutdown
list are discarded with a final shutdown attempt and close. In curl
debug builds, the environment variable `CURL_GRACEFUL_SHUTDOWN` can be
set to make this graceful with a timeout in milliseconds given by the
variable.
The shutdown list is limited to the max number of connections configured
for a multi cache. Set via CURLMOPT_MAX_TOTAL_CONNECTIONS. When the
limit is reached, the oldest connection on the shutdown list is
discarded.
- In multi_wait() and multi_waitfds(), collect all connection caches
involved (each transfer might carry its own) into a temporary list.
Let each connection cache on the list contribute sockets and
POLLIN/OUT events it's connections are waiting for.
- in multi_perform() collect the connection caches the same way and let
them peform their maintenance. This will make another non-blocking
attempt to shutdown all connections on its shutdown list.
- for event based multis (multi->socket_cb set), add the sockets and
their poll events via the callback. When `multi_socket()` is invoked
for a socket not known by an active transfer, forward this to the
multi's cache for processing. On closing a connection, remove its
socket(s) via the callback.
TLS connection filters MUST NOT send close nofity messages in their
`do_close()` implementation. The reason is that a TLS close notify
signals a success. When a connection is aborted and skips its shutdown
phase, the server needs to see a missing close notify to detect
something has gone wrong.
A graceful shutdown of FTP's data connection is performed implicitly
before regarding the upload/download as complete and continuing on the
control connection. For FTP without TLS, there is just the socket close
happening. But with TLS, the sent/received close notify signals that the
transfer is complete and healthy. Servers like `vsftpd` verify that and
reject uploads without a TLS close notify.
- added test_19_* for shutdown related tests
- test_19_01 and test_19_02 test for TCP RST packets
which happen without a graceful shutdown and should
no longer appear otherwise.
- add test_19_03 for handling shutdowns by the server
- add test_19_04 for handling shutdowns by curl
- add test_19_05 for event based shutdowny by server
- add test_30_06/07 and test_31_06/07 for shutdown checks
on FTP up- and downloads.
Closes#13976
This adds connection shutdown infrastructure and first use for FTP. FTP
data connections, when not encountering an error, are now shut down in a
blocking way with a 2sec timeout.
- add cfilter `Curl_cft_shutdown` callback
- keep a shutdown start timestamp and timeout at connectdata
- provide shutdown timeout default and member in
`data->set.shutdowntimeout`.
- provide methods for starting, interrogating and clearing
shutdown timers
- provide `Curl_conn_shutdown_blocking()` to shutdown the
`sockindex` filter chain in a blocking way. Use that in FTP.
- add `Curl_conn_cf_poll()` to wait for socket events during
shutdown of a connection filter chain.
This gets the monitoring sockets and events via the filters
"adjust_pollset()" methods. This gives correct behaviour when
shutting down a TLS connection through a HTTP/2 proxy.
- Implement shutdown for all socket filters
- for HTTP/2 and h2 proxying to send GOAWAY
- for TLS backends to the best of their capabilities
- for tcp socket filter to make a final, nonblocking
receive to avoid unwanted RST states
- add shutdown forwarding to happy eyeballers and
https connect ballers when applicable.
Closes#13904
- decouple need to recv/send from negotiation state, we need
this later in shutdown handling as well
- move ssl enums from urldata.h to vtls_int.h
- implement use of `connssl->io_need` in vtls.c. and all backends
Closes#13879
- add `Curl_hash_add2()` that passes a destructor function for
the element added. Call element destructor instead of hash
destructor if present.
- multi: add `proto_hash` for protocol related information,
remove `struct multi_ssl_backend_data`.
- openssl: use multi->proto_hash to keep x509 shared store
- schannel: use multi->proto_hash to keep x509 shared store
- vtls: remove Curl_free_multi_ssl_backend_data() and its
equivalents in the TLS backends
Closes#13345
