This is currently useful for starting a test server on its own without
an associated test, which can be used for interactive curl testing or
for validating parts of the test harness itself. More commands can be
added to perform additional functions in the future.
Ref: #10818Closes#11008
The test loop now has an initial loop that first runs through all
possible tests to build a set of those to attempt on this run based on
features and keywords and only then goes through that new list to run
them. This actually makes it three loops through all tests cases, as
there is an existing loop that gathers possible test numbers from the
test files on disk.
This has two minor effects on the output: all the tests that will be
skipped are displayed at the start (instead of being interspersed with
other tests) and the -l option no longer shows a count of tests at the
end or a (misleading) statement that tests have run successfully. The
skipped tests are also omitted from the test results sent to AppVeyor
and Azure in CI builds.
Another effect is a reduction in the amount of work considered part of
the "Test definition reading and preparation time" reported with -r
making those figures slightly lower than before.
Ref: #10818
Test 1442's name was not quoted correctly so wasn't registered in
Appveyor and it had the wrong name in Azure. The JSON string quotes were
also invalid, even though both servers happened to accept it regardless.
Closes#11010
The server ports are chosen randomly for each server, but the random
ranges chosen were inconsistently-sized and overlapping. Now, they are
spread out more so at least the first random port chosen for each server
is guaranteed to not also be chosen by another server. The starting port
numbers are also raised to put them in the Ephemeral Port range—not the
range defined by RFC 6335 but the one used by Linux, which starts lower
and gives us more room to work with.
Reported-by: Daniel Stenberg
Calling stopserver() before retrying stunnel due to an error would stop
the dependent server (such as HTTP) meaning stunnel would have nothing
to talk to when it came up. Don't try to force a stop when it didn't
actually start. Also, don't mark the server as bad for future use when
it starts up on a retry.
Reported-by: eaglegai at github
Tested-by: eaglegai at github
Fixes#10976
If a server couldn't be started on a port, a new one is randomly chosen
and the server is tried again. Avoid accidentally using a
randomly-chosen 0 port offset by adding 1 to the random number.
Found-by: Daniel Stenberg
This reduces the startup time when there is a known conflict on the
random port chosen for a server. This was already done for stunnel, but
now it's done for all servers.
testutil.pm now contains a few miscellaneous functions that are used in
several places but have no better place to live. subvariables moves to
servers.pm since most variables that it substitutes relate to servers,
so this is the most appropriate place. Rename a few functions for better
naming consistency.
Ref: #10818Closes#10995
This is code that is directly responsible for running a single test.
This will eventually run in a separate process as part of the parallel
testing project.
Ref: #10818
Otherwise, an HTTP test closely following this one with a tight time
constraint (e.g. 672) could fail because the test server stays sitting
with the wait command for a while.
As the comment states "Address family must be specified before ListenAddress", otherwise the tests fail to run
`"failed starting SSH server" 52 times (582, 583, 600, 601, 602, 603, 604, 605, 606 and 43 more)`
Closes#10983
This script does not work since the introduction of the test
preprocessing. If we need this functionality, it probably needs to be
moved into the runtests tool or similar.
Reported-by: Dan Fandrich
Fixes#10895Closes#10987
- with `--proxy-http2` allow h2 ALPN negotiation to
forward proxies
- applies to http: requests against a https: proxy only,
as https: requests will auto-tunnel
- adding a HTTP/1 request parser in http1.c
- removed h2h3.c
- using new request parser in nghttp2 and all h3 backends
- adding test 2603 for request parser
- adding h2 proxy test cases to test_10_*
scorecard.py: request scoring accidentally always run curl
with '-v'. Removed that, expect double numbers.
labeller: added http1.* and h2-proxy sources to detection
Closes#10967
- move host checks together
- simplify the scheme parser loop and the end of host name parser
- avoid itermediate buffer storing in multiple places
- reduce scope for several variables
- skip the Curl_dyn_tail() call for speed
- detect IPv6 earlier and skip extra checks for such hosts
- normalize directly in dynbuf instead of itermediate buffer
- split out the IPv6 parser into its own funciton
- call the IPv6 parser directly for ipv6 addresses
- remove (unused) special treatment of % in host names
- junkscan() once in the beginning instead of scattered
- make junkscan return error code
- remove unused query management from dedotdotify()
- make Curl_parse_login_details use memchr
- more use of memchr() instead of strchr() and less strlen() calls
- make junkscan check and return the URL length
An optimized build runs one of my benchmark URL parsing programs ~41%
faster using this branch. (compared against the shipped 7.88.1 library
in Debian)
Closes#10935
This helps enforce more modularization and encapsulation. Enable and fix
warnings on a few packages. Also, rename ftp.pm to processhelp.pm since
there's really nothing ftp-specific in it.
Ref: #10818
- Use an absolute path for the -L option since the module isn't in the
perl path
- Create the needed test file in a <file> section; <precheck> isn't
intended for this
- Fix the test number in the file name, which was wrong
Follow-up to f754990a
Ref: #10818Fixes#10889Closes#10917
It's not available on Solaris 10, for example. Since this is just test
code that doesn't need to use an optimized system version, replace it
with the implementation copied from tool_cb_hdr.c.
A typical mistake would be to try to set "https://" - including the
separator - this is now rejected as that would then lead to
url_get(... URL...) would get an invalid URL extracted.
Extended test 1560 to verify.
Closes#10911
