the next release is now called 7.19.0

docs/curl.1

@@ -21,7 +21,7 @@
 .\" * $Id$
 .\" **************************************************************************
 .\"
-.TH curl 1 "5 June 2008" "Curl 7.18.3" "Curl Manual"
+.TH curl 1 "5 June 2008" "Curl 7.19.0" "Curl Manual"
 .SH NAME
 curl \- transfer a URL
 .SH SYNOPSIS
@@ -103,7 +103,7 @@ In general, all boolean options are enabled with --option and yet again
 disabled with --\fBno-\fPoption. That is, you use the exact same option name
 but prefix it with "no-". However, in this list we mostly only list and show
 the --option version of them. (This concept with --no options was added in
-7.18.3. Previously most options were toggled on/off on repeated use of the
+7.19.0. Previously most options were toggled on/off on repeated use of the
 same command line option.)
 .IP "-a/--append"
 (FTP) When used in an FTP upload, this will tell curl to append to the target
@@ -289,14 +289,14 @@ away. EPRT and LPRT are extensions to the original FTP protocol, may not work
 on all servers but enable more functionality in a better way than the
 traditional PORT command.
 
-Since curl 7.18.3, \fB--eprt\fP can be used to explicitly enable EPRT again
+Since curl 7.19.0, \fB--eprt\fP can be used to explicitly enable EPRT again
 and \fB--no-eprt\fP is an alias for \fB--disable-eprt\fP.
 .IP "--disable-epsv"
 (FTP) Tell curl to disable the use of the EPSV command when doing passive FTP
 transfers. Curl will normally always first attempt to use EPSV before PASV,
 but with this option, it will not try using EPSV.
 
-Since curl 7.18.3, \fB--epsv\fP can be used to explicitly enable EPRT again
+Since curl 7.19.0, \fB--epsv\fP can be used to explicitly enable EPRT again
 and \fB--no-epsv\fP is an alias for \fB--disable-epsv\fP.
 .IP "-D/--dump-header <file>"
 Write the protocol headers to the specified file.

docs/libcurl/curl_easy_setopt.3

@@ -1458,7 +1458,7 @@ considered as failure.
 A specific error code (CURLE_SSL_ISSUER_ERROR) is defined with the option,
 which is returned if the setup of the SSL/TLS session has failed due to a
 mismatch with the issuer of peer certificate (\fICURLOPT_SSL_VERIFYPEER\fP has
-to be set too for the check to fail). (Added in 7.18.3)
+to be set too for the check to fail). (Added in 7.19.0)
 .IP CURLOPT_CAPATH
 Pass a char * to a zero terminated string naming a directory holding multiple
 CA certificates to verify the peer with. The certificate directory must be
@@ -1485,7 +1485,7 @@ This option makes sense only when used in combination with the
 A specific error code (CURLE_SSL_CRL_BADFILE) is defined with the option. It
 is returned when the SSL exchange fails because the CRL file cannot be loaded.
 Note that a failure in certificate verification due to a revocation information
-found in the CRL does not trigger this specific error. (Added in 7.18.3)
+found in the CRL does not trigger this specific error. (Added in 7.19.0)
 .IP CURLOPT_RANDOM_FILE
 Pass a char * to a zero terminated file name. The file will be used to read
 from to seed the random engine for SSL. The more random the specified file is,

docs/libcurl/libcurl-errors.3

@@ -21,7 +21,7 @@
 .\" * $Id$
 .\" **************************************************************************
 .\"
-.TH libcurl-errors 3 "30 Aug 2007" "libcurl 7.17.0" "libcurl errors"
+.TH libcurl-errors 3 "8 Jun 2008" "libcurl 7.19.0" "libcurl errors"
 .SH NAME
 libcurl-errors \- error codes in libcurl
 .SH DESCRIPTION
@@ -213,9 +213,9 @@ Socket is not ready for send/recv wait till it's ready and try again. This
 return code is only returned from \fIcurl_easy_recv(3)\fP and
 \fIcurl_easy_send(3)\fP (Added in 7.18.2)
 .IP "CURLE_SSL_CRL_BADFILE (82)"
-Failed to load CRL file (Added in 7.18.3)
+Failed to load CRL file (Added in 7.19.0)
 .IP "CURLE_SSL_ISSUER_ERROR (83)"
-Issuer check failed (Added in 7.18.3)
+Issuer check failed (Added in 7.19.0)
 .IP "CURLE_OBSOLETE*"
 These error codes will never be returned. They used to be used in an old libcurl
 version and are currently unused.